Let's test your knowledge of Etherchannels, Voice protocols, and other important Cisco certification exam topics with these practice exam questions!
™
CCNA / CCENT Certification:
You've just successfully bundled three separate physical trunks into an Etherchannel. What is the net effect on the overall port cost of these links?
A. The Etherchannel will have a single port cost, and it will be lower than that of the separate links.
B. The Etherchannel will have a single port cost, and it will be higher than that of the separate ccna course london links.
C. The Etherchannel will have a single port cost roughly equivalent to that of the separate links.
D. Etherchannels do not have port costs.
Answer: A. The Etherchannel will appear in various Cisco switch commands as "port-channel0", and this virtual interface will appear with a lower port cost than the individual switch ports did previous to the bundling.
CCNA Security:
What is the numeric value assigned to the highest devices in an NTP hierarchy?
Answer: Zero, or "stratum zero" to be more precise.
CCNA Voice :
Which of the following is true of H.323?
A. It's Cisco-proprietary.
B. It's considered a "mature" protocol.
C. It does not support many recent VoIP features.
D. Cisco IP Phones do not support this protocol.
Answers: B, D. H.323 is an industry-standard protocol, not Cisco-proprietary.
CCNA Wireless:
Once a Wireless AP forms an association with a controller, that AP should receive a list of other acceptable controllers. These controllers are collectively referred to as what?
A. mobility group
B. WAP band
C. Oxy Clean
D. Big City Slider Station
E. LWAPP
Answer: That's an IP Mobility Group.
CCNP Certification Questions:
BSCI Exam: Identify the well-known mandatory BGP attributes.
A. AS_PATH
B. Local Pref
C. Atomic Aggregate
D. Origin
E. Next-Hop
Answers: A, D, E. The well-known mandatory BGP attributes are AS_PATH, origin, and next-hop.
BCMSN Exam:
Arrange the following four switching methods in order of speed, fastest to slowest.
A. Fast Switching
B. CEF
C. Process Switching
D. Distributed CEF
Answer: From fastest to slowest: Distributed CEF, CEF, Fast Switching, Process Switching.
ISCW Exam:
You're configuring a VPN with SDM, and you're configuring the Connection Information section. What authentication options will you be presented with?
A. PSK
B. TACACS+
C. AAA
D. Digital Certificates
E. RADIUS
Answers: A, D. The choices are Pre-Shared Keys (PSK) and digital certificates.
ONT Exam:
What common term refers to the process of process of assigning the packet a value reflecting the level of QoS it should receive and then placing that packet into a queue in accordance with that level of QoS?
Answer: That's marking and classification.
Look for more Cisco certification practice exam questions, tutorials, and training videos on my website!
CCNA exam success depends partially on knowing the details of ISDN, and there are plenty of them! To help you review for your CCNA exam, here are a few ISDN details that you must know on exam day. (They help in the real world, too - and there are still plenty of ISDN networks out there!
The Cisco-proprietary version of HDLC is the default encapsulation type for serial and ISDN interfaces.
R2#show interface serial0
Serial0 is up, line protocol is up
Hardware is HD64570
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set, keepalive set (10 sec)
While there's only one D-channel in BRI, PRI (US) and PRI (EU), the bandwidth of that D-channel does vary from BRI to PRI. It's 16 kbps in BRI and 64 kbps in both PRI versions.
The global command isdn switch-type must be configured before you can even begin to have ISDN work. show isdn status will tell you whether or not you've done this correctly.
R2#show isdn status
**** No Global ISDN Switchtype currently defined ****
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = none
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
PAP allows passwords to be different; CHAP requires that they be the same.
PAP requires the "ppp pap sent-username" interface-level command. CHAP has no equivalent command.
Define interesting traffic with dialer-list and link that list to the interface with dialer-group.
R2#conf t
R2(config)#dialer-list 1 proto ip permit
R2(config)#int bri0
R2(config-if)#dialer-group 1
The dialer idle-timeout value is expressed in seconds, not minutes. (Even IOS Help isn't totally clear on this.)
R2(config)#int bri0
R2(config-if)#dialer-group 1
R2(config-if)#dialer idle-timeout ?
Idle timeout before disconnecting a call
R2(config-if)#dialer idle-timeout 120
Dialer map maps a remote IP address to a remote phone number. You never dial the local router's phone number.
dialer load-threshold requires the ppp multilink command to be configured, and the value of dialer load-threshold is expressed as a ratio of 255, NOT 100. For example, if you want the second b-channel to come up when the first reaches 50% of capacity, the value to express with dialer load-threshold would be 50% of 255 - which equals 127.
R2(config)#int bri0
R2(config-if)#encap ppp
R2(config-if)#ppp multilink
R2(config-if)#dialer load-threshold ?
Load threshold to place another call
Success on the CCNA exam depends on knowing the details. Keep studying, keep practicing on real Cisco routers and switches, keep a positive attitude, and you're on your way to CCNA exam success!
Welkom bij
Beter HBO
© 2024 Gemaakt door Beter HBO.
Verzorgd door
Je moet lid zijn van Beter HBO om reacties te kunnen toevoegen!
Wordt lid van Beter HBO